Home / Kitchen Renovation Guides / Replacing a Kitchen Splashback

Field notes — Splashback guide

Replacing a kitchen splashback: check the wall before you choose the finish.

Written by Ivan Bodnar, Independent Home Renovation Specialist · Related: Chapter 07 — Tiling and Kitchen Splashbacks

SHORT ANSWER

In many kitchens, yes, the splashback can be replaced without redoing the whole kitchen. Whether that’s practical depends on four things: how the old splashback comes off, what condition the wall is in behind it, how the power points sit, and whether the new finish suits the benchtop and cabinets you’re keeping.

Field A — Removal

Taking the old splashback off

Tiles are usually bonded to the wall with adhesive, and removing them often takes some of the wall surface with them. Sheet splashbacks may be glued, fixed or both. Before anything comes off, I look at how the existing splashback is fixed, whether it continues behind the rangehood or under the wall cabinets, and how it meets the benchtop.

Any benchtop and cabinets that are staying need protecting during removal. Where the old splashback runs behind appliances or cabinetry, that affects how much has to come out and where the new edge lines will finish. These details are worth settling at the on-site assessment, not halfway through the job.

FIELD B — THE WALL BEHIND

A new splashback is only as flat as the wall it sits on.

Once the old splashback is off, the wall’s real condition shows: torn plaster paper, ridges of adhesive, old fixing holes and, near the sink or cooktop, sometimes signs of moisture. If you put new finishes on before checking for moisture, substrate suitability, service access and underlying damage, you can end up with avoidable rework.

Preparation might mean grinding back adhesive, patching or replacing sections of plasterboard, and checking the wall is flat enough for the material you’ve chosen. Large panels show unevenness more than small tiles. An inspection can’t reveal every concealed issue, so I check the wall again once it’s exposed. More on this in Surface Preparation and Hidden Conditions.

A bright modern kitchen corner with glossy white cabinets, under-cabinet lighting, a large chrome mixer tap, and wall power outlets.

Reference photo: wall outlets beside a mixer tap. What to check: how the outlet cut-outs line up with the joints and the cabinet edges.

Field C — Power points

Setting out around power points

Switches and power points sit inside the splashback zone, so the set-out has to work around them. I plan the tile joints or panel cut-outs so each outlet sits neatly instead of straddling a joint, and I check that cover plates will sit properly over the new finished thickness.

If a power point needs to move, be added or be changed, a licensed electrician does that work. The same goes for changes to the tap or plumbing, which a licensed plumber handles. I don’t carry out licensed electrical or plumbing work myself. See Licensed Trades for Plumbing and Electrical.

Field D — Matching

Matching what's staying

A splashback sits between two surfaces you may be keeping. It should suit both of them.

Benchtop
Look at colour and pattern alongside the benchtop, and at the joint where the two meet, which needs a suitable sealed finish. If you’re planning to replace a worn benchtop soon, it usually makes sense to do that first, because the splashback sits on top of it.

Cabinetry
Think about door colours, handles and how long the existing cabinets will stay. A new splashback can make tired doors look more worn. Read Worn Benchtops and Cabinets: Repair, Reuse or Replace.

Edges and ends
Decide where the splashback stops: at a window reveal, at the end of a run, or up to the rangehood. Exposed edges need a finished edge or trim, chosen to suit the material.

BEFORE THE ASSESSMENT

☐ Note any cracked, loose or stained areas of the current splashback.
☐ Decide whether the benchtop and cabinets are staying.
☐ Mark any power point you’d like moved or added.
☐ Take a few photos of the full run, including the ends.

If you’re thinking about a new splashback in Malvern, I can look at the wall, fixtures and edges on site and then prepare a free written quotation. For more, see How to Prepare for an On-Site Kitchen Assessment and What May Be Found Behind Kitchen Cabinets.

Ivan Bodnar is an independent sole trader and does not personally claim unverified trade licences or builder registration. Licensed plumbing and electrical work is done by appropriately authorised specialists. Project scope, permits, registration, insurance and licensed trade requirements vary from job to job.