Home / What to Check: Kitchen Condition Reference

Reference sheet — existing kitchens

What to check in an existing kitchen before anything gets replaced.

This page is a reference sheet rather than a gallery. It covers five places in a worn or ageing kitchen where its condition usually shows first, and for each one it explains what to look at and why it affects the scope of a kitchen renovation in Malvern. I’m Ivan Bodnar, an independent home renovation specialist. These are the same things I look at during an on-site assessment. The photos are general reference images of typical conditions. They don’t show my own jobs.

An older wood-panelled kitchen with extensive cabinetry, dated appliances, a double sink, patterned flooring and a skylight.

Reference photo: an older timber-panelled kitchen with a double sink and patterned flooring. Look past the finishes. Check the sink run, the cabinet bases and the line where the floor meets the kickboards.

FIVE PLACES TO LOOK FIRST

Open the doors, pull out the drawers and run a hand along the edges. You don’t need tools to spot most of these, but you’ll get more out of an on-site assessment if you’ve already looked.

Chapter 02 — Cabinetry

Cabinets and benchtops

These three checks tell you how much of the existing joinery is worth keeping. They also show whether new doors and hardware make sense, or whether the carcasses themselves need replacing. For more detail, see Layout, Cabinetry and Practical Options.

CHECK 01

Under the sink

What to look at: a swollen or flaking cabinet base, water staining, soft spots, the condition around pipe penetrations and any musty smell.

Why it matters: moisture is most likely to show up in the sink run. If the cabinet base or the floor beneath it is damaged, putting new doors on the old carcass won’t fix it. Any change to the pipes themselves is work for a licensed plumber. Read more in What May Be Found Behind Kitchen Cabinets.

CHECK 02

Hinges and drawer runners

What to look at: doors that have dropped or won’t close square, screw holes pulled out of the panel, and runners that bind, rattle or sag under load.

Why it matters: worn hardware on sound panels can often be replaced. Torn-out fixings and soft board point to carcasses that are past reuse. That difference decides between new fronts and new cabinets. See Worn Benchtops and Cabinets: Repair, Reuse or Replace.

CHECK 03

Benchtop edges and joints

What to look at: edge strips that are lifting, swelling at joins near the sink and cooktop, chips along the front edge and how the benchtop is supported underneath.

Why it matters: a worn edge may only be cosmetic. It can also mean water has reached the core. If you want more bench space, the existing supports and layout affect what’s practical. See More Storage and Bench Space Without Starting Over.

An unfinished interior showing drywall, exposed ductwork, plumbing lines, electrical points and a concrete floor.

Reference photo: an unfinished interior showing wall linings, plumbing lines, electrical points and a concrete floor. Every finish in a kitchen sits on this layer.

Chapter 03 — Surfaces

Walls, floors and what runs behind them

CHECK 04

The wall behind the splashback

What to look at: cracked or drummy tiles, grout that stays damp near the sink and, once the tiles come off, torn plaster, old adhesive and patched cut-outs.

Why it matters: a new splashback will only be as flat and secure as the wall behind it. See Replacing a Kitchen Splashback and Plasterboard Installation and Plastering.

CHECK 05

The floor along the cabinet line

What to look at: gaps under the kickboards, a slope along the run, soft or springy areas, and whether the old floor continues under the cabinets.

Why it matters: the floor sets cabinet levelling, benchtop height and appliance clearances. It also decides whether new flooring goes down before the cabinets or after them. See Uneven Floors and a New Kitchen and Flooring.

Plumbing and electrical. Where the water, waste and power points sit shapes the layout options. Any change to them is done by appropriately authorised specialists, not by me personally. Licensed Trades for Plumbing and Electrical explains how this works.

A photo shows the surface. The assessment looks behind it.

These five checks are a starting point. An inspection can’t reveal every concealed issue, and some conditions only show once cabinets or tiles are removed. Project scope, permits, registration, insurance and licensed trade requirements also vary from job to job.

That’s why the free on-site kitchen assessment comes first. The written quotation follows it and is based on what’s actually there.

Further reading

Before the assessment

If you’ve worked through the checks above, these guides cover each one in more depth. The full list is in Kitchen Renovation Guides.

If you’ve spotted something in your own kitchen and want it looked at properly, send me an enquiry. I’ll review it and we can talk about an on-site assessment of your kitchen in Malvern.